The Right Vacuum, Built Right

— From Component To System.

The Right Vacuum, Built

Right — From Component To System.

* Service-Vacuum Consulting

Gas analysis begins with vacuum. el provides expert consulting on vacuum system design, optimal component selection — fittings, valves, regulators, pumps, and gauges — custom pumping station builds, on-site troubleshooting, and equipment rental. Whether you need a single fitting or a complete multi-port high-vacuum station, el delivers solutions optimized for your process and budget.

* WHY EXPERTISE 01

Vacuum Pressure Range Reference

Accurate gas analysis begins with the right vacuum environment. Even the most advanced analyzer cannot deliver reliable results if the system fails
to achieve and maintain its target pressure. Understanding vacuum pressure ranges is essential for selecting the proper operating conditions across different applications.

Vacuum Pressure Range Reference
Rough Vacuum
Medium Vacuum
High Vacuum (HV)
Ultra-High Vacuum (UHV)
1,000 ~ 1 hPa Load lock, industrial
1 ~ 10⁻³ hPa CVD, sputtering, coating
10⁻³ ~ 10⁻⁷ hPa Semiconductor etch, QMS
< 10⁻⁷ hPa Surface science, quantum

* WHY EXPERTISE 02

Four Service Pillars

Backed by 20 years of vacuum engineering expertise, el delivers end-to-end solutions from consulting and custom design to component supply and system rental.

01

Vacuum Consulting

Expert assessment, pressure range analysis, component compatibility review, leak diagnosis

02

Custom Design

End-to-end custom pumping stations — benchtop to multi-port high-vacuum stations

03

Component Supply

KF/CF/ISO fittings, gate/butterfly/needle valves, regulators, MFCs, vacuum gauges

04

System Rental

Short-term rental of gas analysis systems and vacuum pumping equipment

* Consulting & Custom Design

Vacuum System Consulting

el's consulting service helps optimize vacuum performance through system architecture review, component
compatibility assessment, leak diagnostics, and vacuum system integration for reliable gas analysis.

System Architecture Review
Pump selection, piping layout, valve placement, conductance path, and bottleneck identification
Component Compatibility Audit
Seal, valve body, and fitting compatibility with process gas chemistry — critical for corrosive environments
Leak Detection & Troubleshooting
Systematic diagnosis of vacuum leaks, virtual leaks, and outgassing sources; supported by el's QMS capability
Pump Selection Advisory
Matching pump technology (scroll, turbomolecular, rotary vane, ion, cryo) to application requirements
Pressure Control Optimization
Throttle valves, butterfly valves, and electronic pressure controllers for stable CVD/etch/analytical pressures
New System Integration
Advisory for integrating QMS, OES, or FTIR into existing vacuum infrastructure; foreline management & contamination prevention

* Consulting & Custom Design

Custom Pumping Station Design (ivacuum)

Custom-built vacuum stations designed for each application, pressure range, and process condition.

Configuration
Target Application
Key Features
Benchtop Single-Port
R&D labs, university research, single instrument support
Compact footprint, scroll or turbo pump, KF/CF flange
Multi-Port HV Station
Multi-chamber research, advanced materials development
Independent ports, gate valve isolation, shared turbo + backing pump
Process-Integrated Station
Semiconductor/display fab analytical instrument integration
Corrosive-gas compatible (SUS316L, PTFE seals), remote monitoring, interlock
Custom UHV Configuration
Surface science, particle physics, quantum device research
Ion/NEG pump, bakeable CF flanges, pressure ≤ 10⁻⁹ hPa

From Design To Deployment.

Supporting The Entire Vacuum Infrastructure Lifecycle.

* Component Supply & Equipment Rental

The right part, chosen by someone
who understands your process.

Component selection in vacuum systems requires understanding of pressure range, gas chemistry, flow requirements, and long-term
compatibility. el's engineers select and supply components with the same depth of knowledge applied to our own analytical systems.

Category
Typical Components
Key Selection Criteria
Fittings & Flanges
KF (ISO-QF), CF (ConFlat), ISO-F, VCR, Swagelok-compatible, reducers, crosses, tees
Vacuum level, connection frequency, material (SUS304/316L, Al), gasket type
Valves
Gate, butterfly (manual/motorized/pneumatic), angle, needle, ball, vent valves
Pressure range, actuation method, process gas compatibility, flow conductance
Regulators & MFCs
Pressure regulators (inlet/outlet), mass flow controllers, flow meters
Gas compatibility, flow range, pressure differential, corrosion resistance
Vacuum Pumps
Dry scroll, rotary vane, turbomolecular, diaphragm, ion, NEG pumps
Ultimate pressure, pumping speed, process gas type, oil-free requirement
Gauges & Sensors
Pirani, Bayard-Alpert ionization, capacitance manometers, combination gauges
Pressure range, gas-species independence, sensitivity, control output compatibility
Seals & Accessories
O-rings (Viton, Kalrez, PTFE-encapsulated), copper/Al gaskets, blank flanges, feedthroughs
Temperature compatibility, chemical resistance, bakeable vs. non-bakeable requirement

* Component Supply & Equipment Rental

Equipment Rental Service

High-performance gas analysis and vacuum systems represent significant capital investment. el's rental service lets you verify instrument suitability,
cover temporary analytical needs, or support short-duration R&D projects — without the commitment of ownership.

isepa / isepa-s
(QMS Gas Analysis)

On-site gas analysis campaigns, R&D characterization, and instrument evaluation before purchase.

Use Cases

On-Site Analysis
R&D Characterization
Instrument Evaluation

el Support

• On-site engineer available

• Calibration maintained by el

icomby (GHG Measurement)

Short-term GHG scrubber efficiency campaigns and temporary KOLAS measurement capacity support.

Use Cases

GHG Measurement
Scrubber Evaluation
KOLAS Capacity Support

el Support

• KOLAS-valid measurement support

• Test reports available upon request

itof (TOF-MS Analyzer)

Process development gas composition studies and monitoring program evaluation for R&D and pre-production environments.

Use Cases

Process Development
Process Development
Monitoring Evaluation

el Support

• Application setup support

• Suitable for R&D and pre-production development

Vacuum Pumping Stations

Temporary pumping capacity for maintenance periods, backup support during pump service, and custom R&D laboratory setup.

Use Cases

Maintenance Support
Backup Pumping
R&D Lab Setup

el Support

• Configuration matched to customer requirements

• Pressure range optimized for application needs

* Service Process

From Consultation To Working System

From first question to working system — el guides every step.

STEP 01

Consultation & Requirements

Target vacuum level, process gas, chamber config, spatial constraints, budget, and timeline

STEP 02

Design & Component Proposal

System architecture proposal or component selection list; design drawings for custom pumping stations

STEP 03

Supply, Build & Installation

Component supply from verified sources or complete assembly; on-site installation support available

STEP 04

Support & Follow-Up

Post-installation performance verification; ongoing support for follow-up needs and system expansion

* What Sets Apart

Beyond Components, Built On Expertise.

20 years of vacuum engineering experience, from component selection to complete system design.

01

Operator's Perspective

el's own QMS and mass spectrometry systems operate in the 10⁻⁴ to 10⁻⁶ hPa range. Every component we recommend has been evaluated against the same standards we apply to our own instruments.

02

Gas Analysis Integration

el provides both vacuum consulting and gas analysis services — uniquely positioned to diagnose problems at the interface between the vacuum system and the analytical instrument.

03

20 Years Across Diverse Applications

From semiconductor process chambers and OLED deposition systems to power generation SF₆ equipment and university research setups — el has solved vacuum challenges across a wide spectrum of industries.

04

End-to-End Accountability

Whether a single fitting recommendation, a complete pumping station build, or a rental with on-site analytical support, el provides a single point of accountability. No need to manage multiple suppliers.

* Target Industries & Applications

Where Vacuum Performance Matters

From semiconductor fabs to advanced research facilities, el delivers vacuum solutions tailored to industry-specific requirements.

Industry
Vacuum Application
Typical Service
Pressure Range
Semiconductor Fab
Process chamber, load lock, QMS foreline
Consulting, component supply, QMS integration
HV (10⁻³ ~ 10⁻⁶ hPa)
Display (OLED/LCD)
Deposition chamber, OLED cell outgassing
Pumping station design, component supply
HV (10⁻⁴ ~ 10⁻⁶ hPa)
Power Generation
SF₆ gas handling system, switchgear vacuum
Component supply, system review, gas analysis
Rough to MV
Steel & Metallurgy
Vacuum furnace, ladle degassing, coating
Consulting, valve & fitting supply
MV to HV
Basic Science / R&D
Surface science, quantum devices, beam lines
Custom UHV station design & build, rental
HV to UHV

* Frequently Asked Question

FAQ list

Can el help if I'm not sure what vacuum level I need?

Yes — this is one of the most common starting points for a consulting engagement. el will review your process requirements and recommend an appropriate vacuum architecture. You do not need to arrive with a specification already defined.

Can el diagnose a vacuum problem in my existing system without replacing it?

Yes. el's consulting service includes troubleshooting — identifying leaks, virtual leaks, outgassing sources, conductance bottlenecks, and component failures. We use our in-house QMS gas analysis capability to characterize residual gas composition.

Can el design a system compatible with corrosive gases like NF₃, HF, or SF₆?

Yes. Material selection — SUS316L bodies, PTFE or Kalrez seals, and compatible valve coatings — is a standard part of our consulting and component supply process for corrosive gas environments.

Do you supply standard commercial vacuum components, or only custom-built systems?

Both. el supplies standard vacuum components (KF/CF fittings, valves, gauges, regulators, pumps) and designs complete custom pumping stations (i-vacuum product line). For standard components, el adds value through expert selection guidance.

Do you offer on-site installation support for custom pumping stations?

Yes. el can provide on-site delivery, installation, and commissioning support. Remote installation guidance is also available for customers with experienced vacuum technicians on-site.

* CONTACT US

Tell us your vacuum challenge
— we'll design the solution.

Whether you need a single fitting, a complete custom pumping station, an expert consultation on a performance issue, or short-term equipment rental
— el provides the vacuum expertise and analytical depth to help you get it right. Contact us to start the conversation.